LED Footwell Lighting Complete,How to pics uploaded!!

Twingo Forum

Help Support Twingo Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Hows the how to coming along? Because this looks amazing and I fancy some blue strips in mine
 
Courtney":16zdntlx said:
Oh yeah good idea.. The light in the boot comes on when he doors are open.. Meaning it wont come on when the light is turned on in the front. Good thinking ;-)

Yup,Thanks :D
 
Dutchie":1c08uwhm said:
haha, alright, that was the only interiorlight I could think of, that you could use for a fading result, glad you made it work! :cool:

just another question, how did you lead the wire to the front?

Thx!
Yea well thanks it was your idea to run it from the boot :D ,Ive ran it through the trim,I will get pics up this weekend...
 
madmatt":3492kwko said:
Those lights would make me sneeze!

So bright!!! Good job though, can't imagine you'd ever lose anything in that footwell :p

Cheers mate,Yea i know :roll:
 
jra3d":3j94zast said:
Hows the how to coming along? Because this looks amazing and I fancy some blue strips in mine

Cheers mate :) ,I will do the How To this weekend,Ive just been so busy and my car has been at Renault..
 
That's alright mate, know these things take time! Probably could figure out over time just helpful if you've been there and seen it all.
 
Ok everyone here are the how to pics,Sorry they not the best pics :)

Ok 1st u need to remove the boot light,It just unclips.
IMAG0205Copy.jpg

Unscrew the two screws in the light panel
IMAG0206Copy.jpg

I just peeled back the rubber on both cables,I did not cut it,You an cut it if you want.
IMAG0207Copy.jpg

I then added on some cable with a plug connector.
IMAG0208Copy.jpg

Then i removed the side back panel,Theres a black plastic round thing on the bottom just use a flat head and unscrew it,Then open the passanger door and u will find a screw on the same panel,Unscrew it and it just unclips,I did not pull the whole thing off.
IMAG0211Copy.jpg

Then start to feed the cable through the panel to the front(i used 2mitres of cable)
IMAG0212Copy.jpg

Then tuck it behind the bottom panel,You can see in the pic.
IMAG0213Copy.jpg

Then start to feed the cable under the rubber trim,There is a slight gap so use a flat head screw driver and just poke it in the gap.
IMAG0215Copy.jpg

Then run it till then end of the trim,I put my cable under the cubby hole.
IMAG0216Copy.jpg

I used a connector then just plugged them in,I stuck the LEDs up with double sider tape.
IMAG0217Copy.jpg

IMAG0219Copy.jpg

I stuck some LEDs on to velcro.
IMAG0220Copy.jpg

Then put them under the back seats,I ran the cables to the boot light as well :D .
IMAG0222Copy.jpg

They are sooo cool,They turn on when i unlock the doors,They fade out when i start the engine with the other lights and when i lock the doors they fade out as well :D
IMAG0221Copy.jpg

IMAG0222Copy.jpg

Hope this helps!!!
 
The leds are really cheap and it's honestly not hard to do :)
 
Blondie":3qs8hef5 said:
TheDon":3qs8hef5 said:
The leds are really cheap and it's honestly not hard to do :)


Yea that's easy to say when you've got them!
Haha, I promise it's not hard , just follow the how to pics and you will be able to do it :grin:
 
Looks like something I need to do on my Dini once my exams are over, list is getting bigger and bigger
 
Some LEDs to light the glove box wouldn't go amiss either... Just a few in the top or side.
 
Top